How to make a table (out of an old telephone table)

Updated December 26, 2012, 12:00 am Yahoo!7

Rating:

Reuse an old telephone table to make a new more chic table. Remember when you actually had to sit down next to your phone to take a call? Your old rotary dial probably had pride of place on the telephone table – ring any bells? Well, as technology has moved on, this once vital piece of furniture has been left by the wayside. But its new job needn’t be collecting dust in the shed. Bring it out of hiding and turn it into a functional coffee table, oozing with retro flair.

&nbps;

Gather your supplies

  • 1200 x 600 x 18mm plywood
  • 6 x 6mm DAR Tasmanian Oak, or similar, length to suit
  • 6mm toughened glass, cut to suit
  • Notes:

    1. Adjust material quantities to suit table dimensions. 2. Measure table and have components A-E cut at a hardware store from 18mm plywood.

    Here's How

    • Step 1: Remove padded seat from table. It’s likely to be held on with wing nuts underneath table.
    • imageTitle
      Step 2: To create S-shaped sleeve that sits on top of table, position components A and B, using Telephone Table Diagram as a guide (above right) and form a butt joint. Glue, predrill, countersink, then screw together at join with evenly spaced screws. Continue this way with remaining components to form S-shaped sleeve. Fill screw holes with wood filler, let dry, then lightly sand.
    • imageTitle
      Step 3: Remove drawer and unscrew handle. Lightly sand front of drawer.
    • imageTitle
      Step 4: Undercoat front of drawer and S-shaped sleeve with Dulux 1 Step Primer, Sealer & Undercoat, remembering to leave edges exposed. Let dry. Lightly sand, then apply 2-3 coats of Venus Flytrap to S-shaped sleeve and front of drawer, allowing to dry after each coat.
    • Step 5: Lightly sand table and wipe off dust. Paint top of table and drawer housing in Dulux Black. Allow to dry. Leave legs as bare timber.
    • imageTitle
      Step 6: Mark position of beads for glass top. To do this, set combination square to 6mm (thickness of glass) then run it and a pencil along top of both sides of S-shaped sleeve where glass will sit.
    • imageTitle
      Step 7: Measure and cut beads to size from Tasmanian Oak. Glue then nail both pieces into position.
    • imageTitle
      Step 8: Lightly sand edges of S-shaped sleeve to remove any paint drips. If you tilt your sander on its side, you can run it along sharp plywood edges to create a chamfer detail (a bevelled edge).
    • Step 9: Sit S-shaped sleeve in position on table. From underside, predrill evenly spaced holes through tabletop into edges of S-shaped sleeve, then drive screws in to secure to table.
    • Step 10: Spray table legs and sleeve with 1-2 coats of Cabot’s Cabothane Clear, allowing to dry between coats.
    • Step 11: Reattach old handle or attach a new one. Place drawer back in table. Stick 2 clear furniture bumpers to each side of beads, then position glass panel. Your new coffee table is ready to use.

    You’ll also need

    Dulux 1 Step Primer, Sealer & Undercoat (water based); Dulux Wash & Wear Flat in Black; Dulux Aquanamel Semi Gloss in
    Venus Flytrap (lime green); Cabot’s Cabothane Clear Oil Based spray pack in Satin; combination square; small nails; PVA; drill and drill bits; 8g x 35mm chipboard screws; wood filler; power sander with fine-grit sandpaper; handsaw; painting tools; clear furniture protection bumpers; tape measure; pencil; pull handle (optional)

    Store Locator

    Rob Palmer Picks

    Our Brands

    • Home Beautiful
    • Better Basics
    • Diabetic living
    • Gardens

    Download the yahoo food app

    Download the yahoo food app

    Follow us on pinterest

    Follow us on pinterest